transparent epoxy paint

Some of our DIY customers have had great success by carefully researching and buying the proper tools, but know that if you have never installed a 100% epoxy floor before, you are taking a risk by doing so. However, all previous coats should be deglossed to insure a trouble free bond prior to application of recoats or topcoats. We highly recommend that the kits not be broken down unless suitable weighing equipment is available. soapstone valspar polymers It is best to let the floor remain dry for the full cure cycle. We recommend topcoating with a urethane product to assist in UV-resistance. We sell many types of 100% solids epoxy. Always remember that colder temperatures will require more cure time for the product before recoating or topcoating can commence. If you are interested in a this kind of finish, check out our metallic epoxy floor kit page that includes complete kits and application instructions. PACKAGING INFORMATION 1.5 gallon kits (2.95 gallons net approximately) When applied at 100 sq/ft per gallon, Norklad 100-UV willself-levelto a glasslike surface. TOPCOAT: Urethane topcoat is recommended for added UV-Resistance if exposed to sunlight. (1 gal of part a (resin) and half gallon of part b (hardener). Improper mixing may result in product failure. A properly installed 100% solids floor will last for 20 years or more.However, 100% solids epoxy has an extremely short potlife and cure time of only 30 minutes. See the front side of this technical data for primer information. COLOR: Clear Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website.

A test should be made to determine that the concrete is dry; this can be done by placing a 4X4 plastic sheet on the substrate and taping down the edges. Full cure (heavy traffic): 2-7 days @ 70 degrees F VOLATILE ORGANIC CONTENT: Nearly zero pounds per gallon Due to supply shortages throughout the entire chemical industry; we have limited supplies of various epoxy, urethane and color chip flakes. 100% solids epoxy is the only epoxy that can be used for metallic epoxy floors (pictured above). FLOOR CLEANING: Caution! Norklad 200 is a two component 100% solids epoxy colored coating designed for applications where a high build colorfast impact resistant floor is needed. You also have the option to opt-out of these cookies. Pot life - 1 1/2 gallon volume: 20-30 minutes @ 70 degrees F PRODUCT STORAGE: Store product at normal room temperature. COMPRESSIVE STRENGTH: 11,200 psi @ ASTM D695 After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. This gives it the name '100% solids.' It must be applied quickly and skillfully with a notched squeegee by a professional or there is a high likelihod that it will cure faster than it can be applied. 100% solids epoxy is considered the industry standard for high-end flooring due to the fact that it is 4x stronger than concrete and has no voc, no flammability and can be applied as thick or thin as you need it. Norklad 100-M is a two component 100% solids epoxy broadcast coat that can be filled with decorative chips and colored sand mixtures to provide an infinite array of color schemes or patterns. Norklad 100-UV is a two component 100% solids epoxy broadcast coat that can be filled withdecorativechips and colored sand mixtures to provide an infinite array of color schemes or patterns. There are no harmful organic vapors (VOCs) like you experience with urethane application. Improper mixing may result in product failure. TENSILE STRENGTH: 7,600 psi @ ASTM D638 COLORS: Light Gray, Medium Gray, Charcoal, Off White, Beige, Tan, Wheat, Taupe, Tile Red, Royal Blue, Steel Blue, Black, White Continuous storage should be between 60 and 90 degree F. Low temperatures or temperature fluctuations may cause product crystallization. PRODUCT APPLICATION: The mixed material can be applied by brush, roller or a serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained.

Standard packages are packaged in 1.5-gal kits. 100% solids epoxy does not have water or solvents that evaporate while curing; it retains 100% of its thickness and body after cure. PRODUCT APPLICATION: The mixed material can be applied by brush or roller. Then broadcast aggregate into the coating while wet. tack free (dry to touch): 5-8 hours @ 70 degrees F pot life 1 1/2 gallon volume: 30-50 minutes @ 70 degrees F We will do our best to keep accurate stock availability online. VOLATILE ORGANIC CONTENT: Zero pounds per gallon If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. ADHESION: 350 psi @ elcometer (concrete failure, no delamination) APPLICATION TEMPERATURE: 55-90 degrees F, pot life 1 1/2 gallon volume .. 20-30 minutes @ 70 Ftack free (dry to touch)6-8 hours @ 70 Frecoat or topcoat.. 10-16 hours @ 70Flight foot traffic..14-18 hours @ 70Ffull cure (heavy traffic) 2-7 days @ 70F, CHEMICAL RESISTANCE:REAGENT RATINGbutanol Cxylene C1, 1, 1 trichloroethane BMEK Amethanol Aethyl alcohol Cskydrol B10% sodium hydroxide E50% sodium hydroxide D10% sulfuric acid C70% sulfuric acid A10% HC1 (aq) C5% acetic acid B. All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate. TENSILE STRENGTH: 7,600 psi @ ASTM D638 If a blush is present, it can be removed by any standard detergent cleaner prior to topcoating or recoating. TENSILE STRENGTH: 4,800 psi @ ASTM D638 SOLIDS BY VOLUME: 100% (+/- 1%) TOPCOAT: Urethane topcoat is recommended for added UV-Resistance if exposed to sunlight. We highly recommend that the kits not be broken down unless suitable weighing equipment is available.

(wait until you can no longer leave an imprint of your finger in the coating.) Required fields are marked *, This website uses cookies for the best browsing experience. ULTIMATE ELONGATION: 4.1% SOLIDS BY VOLUME: 100% i. PRODUCT MIXING: This product has a mix ratio of 12# part A to 4.15# part B or two parts A to one part B by volume for standard colors. Orders placed over the next few months may be delayed or will be refunded. If used alone, it is recommended that a primer coat be used to prevent outgassing/blistering. ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles = 32 mg loss It is 100% solids therefore has low odor, no flammability, and is self-leveling. If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking off. Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. Norklad 100-UV has additional UV inhibitors to slow down ambering in the presence of UV light. ULTIMATE ELONGATION: 3.1% SOLIDS BY WEIGHT: 100% COVERAGE PER GALLON: 90-100 square feet per gallon @ 16-18 mils MIX RATIO: 9.0 pounds part A (.99 gallons) to 4.15 pounds part B (.49 gallons) (volumes approx.) SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast or diamond grind) to remove all laitance and provide a suitable profile.

Apply your basecoat and colorchips and allow to sufficiently cure. A test should be made to determine that the concrete is dry; this can be done by placing a 4'x4' plastic sheet on the substrate and taping down the edges. It is 100% solids therefore has low odor, no flammability, and is self-leveling. Standard packages are packaged in 1.5-gal kits. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. SOLIDS BY VOLUME: 100% Once you get the product out of your mixing bucket it takes much longer for it to tack off. SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast or diamond grind) to remove all laitance and provide a suitable profile. PACKAGING INFORMATION: 3 gallon kits (2.9 3.0 gallons net approximately) If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking off to remove the air entrapped in the coating. CURE SCHEDULE: RECOMMENDED FILM THICKNESS: 16-18 mils APPLICATION TEMPERATURE: 55-90 degrees. GARDNER VARIABLE IMPACTOR: 50 inch pounds direct passed The plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause disbonding. By continuing to use this site, you accept our, 1 gal Rust-Oleum Brands 292514 Clear EpoxyShield Premium Clear Coating, polyurethane has many advantages over epoxy, home improvement centers and paint stores harm more than help, How to Fix or Prevent a Rough Textured Color Flake Coating, G-Floor Garage Mats Review | We Reveal The Good And The Bad, The Poor Reviews and Ruined Expectations of Garage Floor Coatings, Street Outlaws Ryan Martin Applies Nohr-S Polyurea Coating System to His New Shop Floor, How to Eliminate Pet Urine Odors from Concrete and Basements, How To Prep and Recoat an Older Epoxy Floor for a New Coat, What You Should Know About Interlocking Garage Floor Tiles, Why the Best DIY Floor Coating Kits are Single-Part Polyurea, Tips for Filling Contraction and Expansion Joints, How to Easily Repair Your Pitted and Spalled Concrete, Rust Bullet, A Long Lasting Garage Floor Paint has Arrived. This product can be used with random chip broadcasts, full chip broadcasts, or colored quartz. HARDNESS: Shore D = 80. full cure (heavy traffic): 2-7 days @ 70 degrees F, APPLICATION TEMPERATURE: 60-90 degrees F with relative humidity below 85%, SOLIDS BY WEIGHT: 100% (+/- 1%) The plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause disbonding. PRODUCT MIXING: This product has a mix ratio of 9.0# part A to 4.15# part B. It has a very fast pot life (30 minutes) once it's mixed with the converter. Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. NOTE: extensive chemical resistance information is available through your sales representative.

This website uses cookies to improve your experience while you navigate through the website. ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles = 36 mg loss RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. ADHESION: 350 psi @ elcometer (concrete failure, no delamination) Slip Resistant Floor Coating Grit Additives. Before recoating or topcoating, check the coating to insure no epoxy blushes were developed (a whitish, greasy film or deglossing). We sell 100% solids epoxy in both colored and clear. When applied at 100 sq/ft per gallon, Norklad 100-M will self-level to a glasslike surface. SOLIDS BY WEIGHT: 100% Best of all, they are abrasian resistant, chemical resistant, stain resistant, and all-around the most durable floor coating there is, by far. If you are looking for a basic clear coat, look no further than Norklad 100 M. If you are looking for a UV resistant clear coat, upgrade to Norklad 100 UV. Always remember that colder temperatures will require more cure time for the product before recoating or topcoating can commence. Low odor, low VOC formula is ideal for use on interior coated or bare concrete surfaces including garages, basements, workshops and more, Your email address will not be published. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast) to remove all laitance and provide a suitable profile. RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. FINISH CHARACTERISTICS: Gloss (60 to 90 @ 60 degrees @ Erichsen glossmeter) However, the material can also be applied by a suitable serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained.

They are in pre-measured kits and should be mixed as supplied in the kit. *For best results, apply with a nap roller and/or squeegee VOLATILE ORGANIC CONTENT: Zero pounds per gallon After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. Improper mixing may result in product failure. Norklad 100-M can easily coat over any solvent or waterborne epoxies. RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. FINISH CHARACTERISTICS: Gloss (60 to 90 @ 60 degrees @ Erichsen glossmeter) ADHESION: 450 psi @ elcometer (concrete failure, no delamination) Test each cleaner in a small area, utilizing your cleaning technique. If no ill effects are noted, you can continue to clean with the product and process tested. PRODUCT APPLICATION: The mixed material can be applied by brush, roller or a serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained. PRODUCT MIXING: This product has a mix ratio of 9.0# part A to 4.15# part B. These cookies will be stored in your browser only with your consent. HARDNESS: Shore D = 81 COVERAGE PER GALLON: 53-130 square feet per gallon @ 12-30 mils 1.5 Gallon (175+ sq/ft) HARDNESS: Shore D = 81 Then broadcast aggregate into the coating while wet. Tack free (dry to touch): 6-8 hours @ 70 degrees F A test should be made to determine that the concrete is dry; this can be done by placing a 4'x4' plastic sheet on the substrate and taping down the edges. Necessary cookies are absolutely essential for the website to function properly. Before recoating or topcoating, check the coating to insure no epoxy blushes were developed (a whitish, greasy film or deglossing). Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. If a blush is present, it must be removed prior to topcoating or recoating. SIZES: Some cleaners may affect the color of the floor installed.

All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. We also use third-party cookies that help us analyze and understand how you use this website. Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term splash spill, D - 72 hour immersion, E - long term immersion. CLEANUP: Use xylol xylene. These cookies do not store any personal information. CURE SCHEDULE: The base coat must be 100% solids because its self leveling properties allow the pigments to blend together and settle evenly. (wait until you can no longer leave an imprint of your finger in the coating. FLEXURAL STRENGTH: 7,400 psi @ ASTM D790 It is mandatory to procure user consent prior to running these cookies on your website. VISCOSITY: Mixed = 700-1000 cps (typical) FLEXURAL STRENGTH: 5,400 psi @ ASTM D790 COMPRESSIVE STRENGTH: 11,200 psi @ ASTM D695 If a primer is not used, more porous substrates may cause outgassing and possible surface defects. COMPRESSIVE STRENGTH: 9,100 psi @ ASTM D695 1/2" X 1/2" bars We highly recommend that the kits not be broken down unless suitable weighing equipment is available. We recommend topcoating with a urethane product to assist in UV-resistance. light foot traffic: 12-14 hours @ 70 degrees F Standard packages are in pre-measured kits and should be mixed as supplied in the kit. The material in the transfer pail is now ready to be applied onto your basecoat. Before recoating or topcoating, check for epoxy blushes (a whitish, greasy film or deglossing). COVERAGE PER GALLON: 90-100 square feet per gallon @ 16-18 mils Many epoxy coatings and urethanes as well as multiple coats of this product are compatible for use as a topcoat. When to use Norklad 100-M: 100% solids is recommended for warehouses, kitchens, restrooms, and other areas where either a high build clear product is needed or where a decorative filled floor is desired. 100% solids is the industry standard for high-end commercial epoxy flooring. When to use Norklad 100-UV: 100% solidsis recommended for warehouses, kitchens, restrooms, and other areas where either a high build clear product is needed or where a decorative filled floor is desired. PRIMING: A suitable primer should be used before applying this product.

Sitemap 18

transparent epoxy paintplant liners wholesale florida